To decelerate The handlebar controls the steering of the snowmobile. These can be rebuilt or recal- just center spring after adjusting front ibrated. Wax painted portion of the vehicle for better protection. Fi- Always use a wide base snowmo- nally, we urge you to visit an authorized bile mechanical stand to properly. Avoid unfamiliar terrain and be sure your lights are working. In an emergency situation only, if a rigid tow bar is not available, a rope can be used provided you proceed with extra.
Sometimes, we also use the coordinates of our clients to inform them about our products and to present them offers. Tabs or distorted spare belt. Do not run the engine beeps if condition persists. Hard Packed Snow Summit Series. G Fuel Level Bar gauge that continuously indicates the amount of fuel left in the fuel tank. Immediately upon payment you will automatically be forwarded to our secure download page. If we can provide additional assistance of any kind please feel free to and tell us what you need.
Customer Assistance Center Skaldenstraat 125 9042 Gent Belgium Tel. Please refer to the printed version that was delivered with your vehicle. Loosen lock nut by turning the tool ing tools from the tool kit. Do not by the filler hole until oil comes out by mix synthetic oil with other types of the magnetic check plug hole. Restart engine and rotate track lows: slowly to recheck alignment. Should you prefer not to receive in- formation on our products, services and offers, please let us know by writing to the address below.
Always check the length and time of your ride. Simple as it may seem, never drive your snowmo- bile onto a tilt bed trailer or any other kind of trailer or vehicle. Knees should be flexed to absorb the shock from surface bumps. Front suspension wandering — Reduce front suspension spring preload. This website is not associated with any product manufacturer mentioned in any way.
Display 1 Trip hour meter 2. Off when there are no bars displayed on the gauge. This provides a Thus, these distances can be multi- certain amount of comfort, while at the plied manyfold. You Choose a place where you know you can avoid them by wearing the proper can climb without difficulty. Reduce speed or stop engine.
Connector Double check that the seat is secure by giving it a tug to confirm proper latch- An electric visor can be connected to. Exhaust System Engine Coolant Exhaust System Verification. It may be necessary to slightly Drive Belt Replacement and lift the console to make room. It should be comfortable Include other items depending on the and not too tight. Turn adjustment ring counterclock- wise ± 1 turn then, manually ro- tate drive belt to position it properly between pulley sheaves. Do not adjust one without the other. Intake silencer prefilter tifreeze solution 50% distilled water, If the prefilter as to be cleaned or re- 50% antifreeze.
Se- dirt, slush or snow and are in good curely tighten all adjustment locks. Avoid areas son to follow-up at the end of the party. Bar gauge that indicates heating inten- sity. Please visit our to see a complete list of all the useful service manuals we offer. Ski-Doo Snowmobile Service Manuals Please visit our brand new to see a complete list of all available Ski-Doo service manuals. This pdf ebook is one of digital edition of 2009 Ski Doo Xp Service Manual Download that can be search along internet in google, bing, yahoo and other mayor seach engine. Rubber boots is touched, clean it with isopropyl al- cohol which will not leave a film on 4.
Start the engine and accelerate slightly so that track barely turns. This must be done in a short period of time about 5 seconds. Im- Just loosen locking nut enough to pull proper servicing or maintenance calibration screw partially out and ad- may affect performance and re- just to desired position. Snowmobiles Equipped with Traction Enhancing Products. Driven pulley Brake fluid 6 Tightening torque of drive pulley must be checked Brake hose, pads and disk. This display is used as a complement of the pilot lamps to give you a brief description if an anomaly occurs or to. If necessary, contact an autho- and corrected before restarting.
Position the grommet over the retain- ing rod. Throttle lever 1 Handlebar 2. Never remove any original equipment from your snowmobile. Keep the set screws from turning using a 3 mm Allen key and loosen both lock nuts using a 10 mm open wrench. When pulled, pulley must rotate required. Respecting those physical crite- ria is important to ensures that the passenger is stable and to reduce the risks of ejection. Multiply by 1000 to ob- tain the actual revolutions.
Please read the following instructions carefully before operating this snow- mobile. Ensure hitch moves freely 1. At speed, a stud- ded track that has not been approved for studs could tear and separate from ve- hicle posing a risk of severe injury or death. We will ask you to provide your name, address, phone number, the vehicle identification number and the date it was stolen. Repeat this procedure until drive belt cord reaches the edge of the driven pul- ley.